Benbrook Electrical Work That Gets the Cause Right First
We test before we replace. Breakers that trip, lights that flicker, a panel that's out of room, an EV charger for the garage or a generator for the next outage. We handle electrical repair, panel upgrades and backup power for homes in Benbrook, White Settlement and Aledo.
- NABCEP certified
- 5 years in business
- 1-year workmanship warranty
- Fault confirmed before repair
Why Homeowners Call Us
Most electrical callbacks happen because someone fixed a symptom. We spend the time up front to find what actually failed.
- 01
We test, then we talk
A tripping breaker can be a bad breaker, a loose neutral, a failing appliance or a circuit carrying too much. We check with meters and load tests before we name a cause. You hear what we found and how we know.
- 02
No parts thrown at the problem
Swapping parts until something works costs you money and leaves the real fault in the wall. We replace what tested bad and leave what tested good.
- 03
Repair or replace, said plainly
Sometimes an old panel just needs tightened lugs and a new breaker. Sometimes it's done. We tell you which, and why, and you decide.
- 04
Written scope before work starts
You get the scope and price in writing before we cut a wire. If we open a wall and find something new, we stop, show you, and ask before going further.
- 05
We clean up behind ourselves
Drop cloths go down where we work. Drywall dust, wire scraps and old parts leave with us.
Electrical Services for Your Home
With 5 years in business behind us, our work covers most of what a house needs: electrical repair, panel upgrades, lighting installation, EV charger installation, whole-home rewiring, remodel and addition wiring, code corrections, surge protection, and torque and cleans. We also install generators and home battery backup systems, and we service and repair generators. We are NABCEP certified. Every job we finish is backed by our 1-year workmanship warranty.
Panel Upgrades
We measure what your home actually draws, then replace or upgrade the panel so breakers stop tripping and new loads have room.
Electrical Repair
Dead outlets, tripping breakers, flickering lights and warm switches traced to the real fault and repaired so the problem stays fixed.
Lighting Installation
Recessed lights, fixtures, ceiling fans, dimmers and outdoor lighting, installed after we check that the circuit, box and switch can handle them.
EV Charger Installation
Level 2 charger installs in your garage or driveway, with a load check on your panel before any wire gets pulled.
Whole-Home Rewiring
We test and map the wiring in your home, then replace worn or unsafe circuits with new copper wiring, grounded outlets and a clean layout that passes inspection.
Generator Installation
Standby and portable generator hookups, sized from a real load count and wired through a proper transfer switch so power comes back safely.
Generator Service & Repair
We service standby generators and transfer switches, read the fault history and fix the real cause so your backup power starts when the grid goes down.
Home Battery Backup
We measure what your home actually draws, then install and wire a battery backup that keeps the circuits you need running when the grid drops.
Remodel & Addition Wiring
New circuits, outlets and lighting for kitchens, baths and added rooms, laid out after we check what your panel can carry.
Code Corrections
We go through your inspection report line by line, confirm what is really wrong and correct it so the work is ready for a recheck or a closing.
Surge Protection
A surge device at your panel, backed by a grounding check, to guard HVAC boards, appliances and electronics from spikes that start inside or outside your home.
Torque & Cleans
We check your panel under load, then tighten every connection to the maker's spec and clean out dust and corrosion before loose parts turn into heat damage.
About Benbrook Electrician
We're a small electrical company that works on houses. Most of our calls start with something that isn't right: a breaker that won't stay on, outlets that went dead, lights that dim when the AC kicks on. Our job is to figure out why, fix that, and not sell you work you don't need.
We'd rather spend an extra half hour testing than come back next week for the same problem. That habit carries into bigger jobs too. Before a panel upgrade or a generator install, we look at your load and your wiring so the new equipment fits the house it's going into.
- In business
- 5 years in business
- Warranty
- 1-year workmanship warranty
- Certifications
- NABCEP certified
What Moves the Price of Electrical Work
We don't post prices because two jobs with the same name can be very different. A panel swap in an open garage is not the same job as one behind finished cabinets. Here is what changes the number.
After we look and test, you get a written estimate by line item. Nothing beyond it happens without your okay.
- What we find when we test
- A loose connection is a short fix. Burned wiring inside a wall is not. The diagnosis sets the scope, which is why we do it first.
- Access to the work
- Open attics and unfinished garages are quicker. Finished ceilings, tight crawl spaces and long wire runs take more hours. Summer attic heat can also slow the work down.
- Panel capacity
- Adding an EV charger, generator or new circuits may need more room or more amperage than your panel has. That can mean a subpanel or a full upgrade.
- Materials and equipment
- Breaker brand, fixture choice, charger model and generator size all change cost. We'll explain the options and what each one gets you.
- Permits and inspections
- Many jobs need a permit and an inspection. The fees and the time for the inspector's visit are part of the job, and we list them on your estimate.
- Condition of the old wiring
- Older wiring, past DIY work or code problems found along the way can add work. We show you photos before anything extra gets done.
Where We Work
We're based in Benbrook, TX, and work on homes across the west side of the metro. That includes Fort Worth, White Settlement, Aledo, Crowley and Burleson, along with River Oaks, Lake Worth, Sansom Park, Westworth Village and Edgecliff Village.
- Benbrook
- White Settlement
- Fort Worth
- Crowley
- River Oaks
- Aledo
- Sansom Park
- Lake Worth
- Edgecliff Village
- Westworth Village
- Burleson
If you're close by and don't see your town listed, give us a call and we'll tell you if we can get to you.
How a Job Runs
Same steps every time, so you always know what comes next.
- 1
You call and tell us what's going on
Book your service visit by phone. Tell us what you're seeing, when it started and anything that changed recently, like a new appliance.
- 2
We test and find the cause
At the visit we check the panel, the circuit and the devices involved. We take photos of anything worth showing you.
- 3
You get the findings and a written estimate
We walk you through what failed and what it takes to fix it. If there's a cheaper option that will hold up, we tell you about it.
- 4
We do the work and handle the permit
If the job calls for a permit, we file for it and book the inspector with whichever office covers your address. We protect floors, keep the work area tidy and turn power back on as soon as it's safe.
- 5
We check it before we leave
We test the finished work under load and show you what we did. Then we clean up.
Common Questions
Something not covered here? (682) 327-1771
Why do my breakers keep tripping?
Usually it's one of a few things: too much load on one circuit, a short in a device or wire, a ground fault, or a breaker that's worn out. Each one has a different fix. We test the circuit and the breaker to find which it is, so you don't pay for a new breaker when the real problem is a melted outlet.
Do you pull permits?
Yes. If your job needs a permit, we apply for it and line up the inspection with the office that covers your address. The permit cost shows up on your written estimate. We're there for the inspection so any questions get answered on the spot.
How long does a panel upgrade take?
A straight panel swap is usually done in a day, with your power off for part of it. Jobs that need a new meter base or utility coordination take longer to schedule because the utility sets its own timing. We'll tell you what to expect before we book the date.
Will my garage work for an EV charger?
Nearly every garage can take one. What decides the job is your panel. We look at how much spare capacity it has and whether there's a free slot for a 240-volt circuit out to the charger. When both check out, it's a breaker and a wire run. When they don't, we walk you through the choices, such as a charger that limits its own draw or a panel upgrade, and what each one involves.
What warranty comes with your work?
Our work comes with a 1-year workmanship warranty. If something we installed or repaired gives you trouble because of how we did it, call us and we'll come back out to look at it.
Should I get a generator or a battery backup system?
Start with two things: the circuits you can't do without in an outage, and how many hours you need them. A generator handles big loads like central AC and keeps going as long as it has fuel. A battery runs silent and kicks in by itself, but it powers fewer things. We check your panel and that short list, then tell you plainly which one fits.
What is a torque and clean?
It's a maintenance visit for your panel. We tighten connections to the right spec and clean out dust and debris. Loose connections heat up over time, especially on circuits that work hard in the summer, and catching them early prevents damage.
Find Out What's Really Wrong
Tell us what's happening and we'll set a time to come test it. You'll know the cause before you spend money on the fix.