ServicesLighting Installation
Lighting Installation in Benbrook
New fixtures, ceiling fans, recessed cans, dimmers and porch lights, hung on wiring we've checked first. We test the circuit, look at the box and match the switch to the bulbs, so your lights stay steady and don't start tripping a breaker a few weeks later.
New Lights, Checked Before They Go Up
Hanging a light looks simple. Most of the trouble starts behind the ceiling. A fan gets mounted to a box made for a 5-pound fixture. A string of LED cans gets put on a dimmer that was never meant for them. A smart switch goes into a box with no neutral wire. The light works on day one, then hums, flickers or quits.
So we look first. We open the box, check what circuit feeds it and see what else is on that circuit. Then we tell you what will work, what needs to change and why. You get lights that do what you expected, without a second trip to fix the first one.
Lighting Jobs We Handle
Recessed lights
We plan the spacing so light spreads across the room instead of pooling in bright circles. Attics around here get very hot in summer, so we use housings rated to sit right against insulation and nothing has to be pulled back.
Fixtures and chandeliers
Old fixture out, new one in, or a new spot added. Anything heavy goes on a box and bracket rated to carry its weight.
Ceiling fans
Plenty of light boxes can't hold a spinning fan. When yours can't, we swap it for a fan-rated box or add a brace, then balance the blades so the fan runs quiet.
Dimmers and smart switches
The dimmer has to suit the bulbs, or LEDs buzz and flicker. Before you buy a smart switch, we check the box for a neutral wire so it will actually work.
Outdoor and landscape lighting
Porch lights, floods, motion lights and path lights. Outside work gets weather-rated boxes and GFCI protection where code calls for it.
Under-cabinet lighting
Hardwired strips or pucks for kitchens and work areas, with the driver tucked somewhere you can still reach later.
Signs It's Time to Call About Your Lighting
- Lights flicker or buzz
- Often it's a dimmer that doesn't match the LED bulbs. Sometimes it's a loose connection in the box. We find out which before we change anything.
- A room is too dark
- One center fixture rarely lights a whole room. Recessed lights or added fixtures can fix that.
- A fan wobbles or the box looks loose
- That usually means the box was never rated for a fan. It should be fixed before it gets worse.
- Fixtures look scorched or brittle
- Bulbs over the fixture's rating cook the wiring and sockets. Discolored plastic or cracked insulation means it's time for a new fixture and a look at the wire.
- Dark spots outside
- Steps, driveways and side yards with no light are easy to trip in at night. A few well-placed fixtures solve it.
How a Lighting Job Goes
- 1
Start with a quick call
Describe the room or yard and the kind of lights you have in mind. We'll ask what's hanging there now, then pick a time for the service visit.
- 2
Check what's behind the ceiling
At the visit we open boxes, test the circuit and check the switch wiring and attic access. If something won't support the plan, we show you and explain the fix.
- 3
Agree on the plan and price
You get a clear scope: fixtures, boxes, switches and any circuit work. If the job needs a permit, we pull it as required by the local jurisdiction.
- 4
Put it in and test it
Drop cloths go down before any cutting starts. Holes are cut clean, and we only patch where we had to open things up. We turn on every light, run each dimmer through its full range and spin up every fan before we finish.
- 5
Clean up and walk through
We sweep up drywall dust and haul off packaging and old fixtures. Then we show you how the dimmers and any smart controls work.
What Moves the Price of Lighting Work
Every job is a little different, so we price it after we've seen the space. The fixture itself is often the smaller part of the cost. Access, wiring and what we find in the ceiling move the number more.
- Number and type of lights
- Six recessed lights take more time than one swapped fixture. Chandeliers and fans add mounting work.
- Attic and ceiling access
- An open attic above the room makes running wire quick. A second floor above, vaulted ceilings or tight attic space take longer.
- New wiring or circuits
- Adding switches or new runs costs more than reusing existing ones. If the circuit is already loaded, a new circuit may be the right call.
- Box and switch upgrades
- Fan-rated boxes, added neutrals for smart switches and the right dimmers are small parts, but they add up across a room.
- Outdoor runs
- Trenching, conduit and weather-rated parts add to outdoor and landscape lighting jobs.
Lighting Installation Questions
- Can you put a ceiling fan where my light is now?
- Usually, yes. The catch is the box. Most light boxes aren't rated to hold a moving fan, so we check it and swap in a fan-rated box or brace if needed. If you want the fan and light on separate switches, we also check whether the wiring to the switch allows it.
- Why do my LED lights flicker on the dimmer?
- Most of the time the dimmer was made for old incandescent bulbs and doesn't play well with LEDs. Mixing bulb brands on one dimmer can do it too. Less often it's a loose connection. We test to find which one it is, then fix that instead of guessing.
- Do I need a permit for new lighting?
- A straight fixture swap usually doesn't. Adding new circuits, new runs or a lot of recessed lights often does. We tell you at the visit and pull the permit when the job needs one, as required by the local jurisdiction.
- How long does it take to add recessed lights?
- A single room with easy attic access is often done in a day. Rooms with a second floor above or no attic access take longer because we have to fish wire through finished walls and ceilings. We give you a time estimate after we look.
- Will you install fixtures I already bought?
- Yes. We'll check that the fixture fits the box and the weight rating before we hang it. If something doesn't match, we'll tell you before we start, not halfway through.
Better Light Starts With a Look at the Wiring
Give us a call about the room or yard you'd like brighter. We'll book a time to open the boxes, test the circuit and plan your lights around what we find. If the real problem is a wiring fault, our electrical repair work takes it from there.